Soil Testing Equipments

Product Details:

The apparatus consists of:

• Ball and socket assembly 1set
• L Bracket of Dial gauge 4nos
• Connecting pipe set consisting of one 60cms long and two 30 cms long extension with nuts and bolts.

 

Accessories:

• Bridge support (Datum Bar) of welded steel angle, 5 meter span, for positioning and fitting of the dial gauges. (Two are required for the test)
• 750x750x25mm 1nos
• 600x600x25mm 1nos
• 450x450x25mm 1nos
• 300x300x25mm 1nos
• 750x750x25mm 1nos
• 600x600x25mm 1nos
• 450x450x25mm 1nos
• 300x300x25mm 1nos
• Dial gauge 0.01mm x 25mm travel.

Product Details:

The Instrument consist of needle attached to a spring loaded plunger. The stem of which is calibrated to read 0 to 40 kgs in 1 kg division. Long stem is graduated at every 12.5mm to read depth of penetration and for use with needles of larger areas. The small penetration steam is also graduated in 12.5mm division and is used with needles of smaller areas. Needle points one each of 0.25, 0.5, 1.0,1.5,2.0, 3.5, and 6.0 sq.cm. and one tommy pin is supplied. Complete as above in a wooden carrying case.

Product Details:

Standard Cone Penetrometer, (Dial Type, with Digital Timer), the apparatus is used to determine the liquid limit of soil which have low plasticity index. The moisture percentage contents determined when cone with half angle of 30° under a total sliding weight of approx 148gm penetrates 25mm in soil sample gives the liquid limit. The weight of cone together with shaft is approx 80gms. The apparatus consists of a cast aluminium base with an iron stand on which moves aluminium arm. A 15cm dial is fixed on this arm. The dial is graduated from 0-400 in one tenth millimeter sub division. The Apparatus is supplied complete with standard cup of dimension 50mm dia x 50mm depth. Digital Timer Box is supplied with the apparatus to automatically stop penetration after desired time duration. 

Product Details:

We are manufacturer and exporter of Standard penetration Test Kit (SPT )used in soil mechanics.The standard penetration test is an in-situ dynamic penetration test designed to provide information on the geotechnical engineering properties of soil.

Specifications:

• Guide Pipe Assembly, fitted with a driving head on one side having standard "A" drill rod thread a cap on the second side. Drive weight falls freely through a height of 75mm
• Tripod stand, 6 meter high connected by a tie bolt. Each leg is made of three part for easy transport. Complete with pulleys and staring arrangements.
• Tripod stand 5 meter long Each leg is made of two parts. Complete with pulley stirring arrangement.
• Pulley Spare: "A" Drill Rod 1 meter long, "A" Drill Rod 1.5 meter long, "A" Drill Rod 3 meter long, Sampling Auger D – 1452
• Auger Head - 150mm diameter
• Auger Head - 100mm diameter
• Auger Head - 75mm diameter
• Auger Head - 50mm diameter
• Auger Head - 38mm diameter
• Extension Road: 1 meter long for 150mm auger, 1 meter long for 100mm/75mm/50mm/38mm

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Mumbai
• Production Capacity: 10/Month
• Delivery Time: Within 10-15 days
• Packaging Details: Jute Packaging

Product Details:

The use of the in-situ CBR apparatus in large road construction projects has increased considerably in the recent years. This apparatus, mounted on a rolled steel joist cantilevered from the back of the truck or fitted to the underside of a mobile frame, can be used to determine the bearing ratio (generally known as the California Bearing ratio) of soils quickly and efficiently for the evaluation of strengths of sub-grade & bases for roads & runway pavements. This method of testing in-situ, using piston penetration, is useful for determining the load carrying capacity in the field, when the in-place density and water contents are such that the degree of saturation is 80% or greater, when the material is coarse grained and cohesion less so that it is not affected by changes in the water content when the material has been in-place.

Additional Information:

• Item Code: ST-03

Product Details:

We are manufacturer,supplier and exporter of Globetrek Direct Shear Apparatus As Per IS 2720 (Part-XIII) . Loading Unit with V-strips on which shear box housing rests, loading yoke with direct and lever system for applying normal load to the capacity of 8 kg/cm2, fixtures for proving ring, brackets for holding consolidation and strain dial gauges, and manually operated lead screw for application of shear stress. We provide this range at most reasonable rates.

We are having three types of Direct Shear Apparatus As Per IS 2720 (Part-XIII):

• Hand Operated Direct Shear Apparatus
• Motorized Single Speed Direct Shear Apparatus
• Motorized Six Speed Direct Shear Apparatus
• Motorized 12 Speeds Direct Shear Apparatus

Additional Information:

• Port of Dispatch: JNPT
• Production Capacity: 20/Month
• Delivery Time: 2-3 weeks
• Packaging Details: Wooden Packaging

Product Details:

The Rotap sieve shaker reproduces the circular (revolution approx: 280 RPM + 10) & (tapping approx 150 RPM + 10) motion of hand sieving and provides a uniform mechanical action ensuring accurate, dependable and precisely repeatable results. It takes upto 7 sieves with one lid & pan of 200mm dia. Suitable for operation on 230 volts, single phase power supply. Unit is fitted withMechanical Timer. (Supplied without Sieves.)

Product Details:

It is a very simple and robust instrument for rapid in-situ measurement of the structural properties of road pavement. It incorporates a 8 kg weight dropping through a height of 575mmand a 60 Degree cone having diameter of 20mm. It is supplied complete with assembly tools.

The instrument is provided in a wooden carrying case.The Dynamic Cone Penetration Test provides a measure of a material's in-situ resistance to penetration. The test is performed by driving a metal cone into the ground by repeated striking itwith a 17.6 lb (8 Kg)weight dropped from a distance of 2.26 feet (575 mm). The penetration of the cone is measured after each blow and is recorded to provide a continuous measure of shearing resistance up to 5 feet below the ground surface. Test results can be correlated to California Bearing Ratios, in-situ density, resilient modulus, and bearing capacity

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Our Relative Density Test Apparatus is comprehensively used for the determination of the relative density of cohesion less free draining soils. These Relative Density Test Apparatuses are specially designed to meet the essential requirements of the set standards.

Standard:

• IS: 2720 (part XIV)

Accessories:

• Dial gauge 0.01 mm x 50 mm travel
• Extension piece 25 mm for dial gauge

Product Details:

We are manufacturer supplier of Plastic Limit Set. Consists of one each of glass pate, measuring cylinder 25ml, flexible spatula, evaporating dish, brass rod 3mm dia and 6 nos moisture cans packed in a cardboard box.

Additional Information:

• Item Code: ST-14

Product Details:

We are manufacturer supplier of Sand Equivalent Shaker. The unit provides a constant uniform shaking with automatic cycle test. Oscillating excursion is 200 mm at 175 strokes / minute rate. Complete with timer that automatically stops the shaker at the end of the test. Power Supply 230V A.C. 50Hz.

Additional Information:

• Item Code: ST-28

Product Details:

Same as soil Permeability but instead of a set of three glass stand pipes a stand with nine glass tubes of 6mm, 10mm, 20mm, 25mm, 40mm, 50mm, 60mm, 70mm, 75mm, bore tube is provided with over flow arrangement for constant head tests. The remaining tubes are used for falling head test.

Product Details:

Lightweight and compact for easy transport to the field.

The Proving Ring Penetrometer is a 30 degree cone penetrometer used to determine the bearing capacity of subgrades or to measure soil compaction.

Product Details:

We are manufacturer exporter of Soil Lathe Bench Mounting. This instrument is used for preparing soil samples for various tests like Triaxial Test, Unconfined Compression Test etc.

Product Details:

We are manufacturer supplier of Proctor Needles. Proctor Needles ST-24 Proctor needles are used for quick evaluation of maximum soil density in the field. Standard Compaction curves showing moisture contents versus densities are drawn in laboratory using standard compaction method and penetration of the proctor needles are correlated. Proctor needles are also known as Proctor Penetrometers.

Additional Information:

• Item Code: ST-24

Product Details:

75mm diameter Latex Membranes placed over soil samples as a barrier to fluids in pressurized chambers. Made from pure latex rubber, membranes are processed under tightly controlled, proprietary manufacturing standards to maintain high-quality products that are free from defects. Popular sizes are in stock and ready to ship. 

Features:

• Pure latex, manufactured to exacting standards

• Special packaging inhibits premature breakdown

Product Details:

The soil testing equipment is used for determination of the dry density of compact, fine, medium grained soils and for layers not exceeding 50cm thickness. A circular hole is dug into the ground, all the soil from within it collected, weighed and dried, and the hole back filled with a standard uniform sand or fine gravel, poured from a calibrated container for calculating the volume of hole. The complete apparatus consists of a Sand Pouring Cylinder fitted with Conical funnel and Shutter, Cylindrical Calibration Container, and a Metal tray with a central hole.

Product Details:

Rapid Moisture Meter Range:
Uses a technique based on the fact that water will react with calcium carbide to form a gas and that the quantity of gas formed is directly proportional to the water present. The gas pressure is indicated on a built-in pressure gauge. The pressure gauge calibrated in percentage of moisture. as per is: 2720 (part ii) – 1973
The apparatus is supplied in polished wooden carrying case. The apparatus consists of a pressure vessel with clamp for sealing, rubber sealing gasket, pressure gauge in moisture content 0-25% on wet weight basis, a counter poised balance to weigh the sample, a scoop for measuring reagent, one cleaning brush, set of 4 steel balls and one bottle of reagent (500gm).

Optional Accessories:

• Electronic balance of 200 g capacity x 0.1 g readability

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: JNPT
• Production Capacity: 1000/ Month
• Delivery Time: Ready In Stock

Product Details:

This Core Cutter Apparatus is fabricated as per IS : 2720 by using best available raw material. Known as important equipment in soil testing requirements, this Core Cutter Apparatus has huge market demand.

Product Details:

• Cutter is made of steel 100mm dia. x 130mm long with steel Dolly 25 mm high and 100 mm dia.
• Fitted with a lip to enable it to be located on top of the core cutter.
• Supplied complete with steel rammer.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Mumbai
• Production Capacity: 100Month
• Delivery Time: within 7 days
• Packaging Details: Export Worthy Packaging

Product Details:

We are supplier of soil hydrometer. Used for grain size analysis of soils where more than 10% of the material will pass through 75 microns i.s. Sieve. Manufactured from clear transparent glass having uniform clarity throughout the upper end on which density scale is engraved. The scale range is 0. 995 to 1. 030 density (gms/cc) at 27°c. Smallest division on the scale is 0.0005.

Note: hydrometer for other liquids also available.

Additional Information:

• Item Code: ST-10

Product Details:

We are leading manufacturer supplier and exporter of Triaxial Shear Test Apparatus from India Mharashtra Mumbai.

Additional Information:

• Item Code: ST-18
• Port of Dispatch: JNPT (Nhava Sheva)
• Production Capacity: 05 /month
• Delivery Time: 3-4 week
• Packaging Details: Wooden Packing

Product Details:

Unconfined Compression Test apparatus can be used either in a laboratory or in field. These are designed as per the set standard and manufactured using high quality Material.

Specifications:

• Consists of a spring operated load frame with arrangements for loading 38 mm x 76 mm samples
• One set of four load springs of stiffness 0.2 kg, 0.4 kg, 0.8 kg, and 1.6 kg/mm,
• A calibrated mask and one set of 50 charts, in a metal carrying case.

Spares Accessories:

• Charts, set of 50 Calibrated mask. Spring set comprising one each of stiffness 2 N/mm, 4N/mm, 8N/mm and 16 N/mm Coning toll for 38 mm sample (female) Coning toll for 38 mm sample (male) Tripod stand wooden, for using the instrument in field.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

We are manufacturer,supplier of compression proving rings.Proving rings are used for load measurements and are used in outfits of a number of soil/cement bitumen testing equipments like direct shear test apparatus, triaxial shear test apparatus, c.B.R. Test, uncontained test, marshall test etc.They are made out of special steel carefully forged to give maximum strength and machined to give highest sensitivity combined with stability to ensure long life and accuracy.When compressive or tensile load is applied within the elastic range, the proving rings get temporarily deformed. This deformation is measured by a sensitive dial gauge fixed co-axially at the center of proving ring. The dial gauge readings thus obtained versus load applied enable the operator to find out unknown load, just by noting the dial gauge reading for unknown load.The proving rings have high elasticity and on removing load they regain their original shape provided they are loaded in their elastic limits. Salient features a dial gauge and plunger anvil are mounted on brackets clamped to the ring body. The dial gauge is held perfectly rigid without the remotest chance of shifting due to inadvertent shocks or pressures exerted on it.

Specifications:

• Above cap. 50 to 500kg.
• Above cap. 500 to 3000kg.
• Above cap. 3000 to 5000kg.
• Above cap. 5000 to 10000 kg.
• Above cap. 10000 to 20000 kg.
• Above cap. 20000 to 30000kg.
• Above cap. 30000 to 50000 kg.
• Above cap. 50000 to 100000 kg.
• Above cap. 100000 to 200000 kg.
• Above cap. 200000 to 300000 kg

Additional Information:

• Item Code: ST-09

Product Details:

The standard sand shall be of quartz, light grey or whitish variety and shall be free from silt. The sand grains shall be angular, the shape of the grains approximating to the spherical form; elongated and flattened grains being present only in very small or negligible ,quantities. 
4.2 The standard sand shall ( 100 percent ) pass through 2-mm IS sieve and shall be ( 100 percent ) retained on 90-micron IS Sieve with the following particle size distribution:
Particle Size Percent Smaller than 2 mm and greater than 1 mm  33.33 %

Smaller than 1 mm and greater than 500 microns - 33.33%

Below 500 microns but greater than 90 microns - 33.33%

Product Details:

Hydraulic Jacks have multipurpose utility, i.e. application of loads while engaged in field investigation, determination of load carrying capacity of piles in the field, tensioning of wires in pre-stressed structures, loading of members of any structure for deformation characteristics etc. The jacks are supplied complete with manually operated pumping units fitted with bourdon tube type load gauge and high pressure flexible hose pipe. All the jacks have a piston travel of 50 mm and jacks upto 1000 kN capacity are provided with retraction springs. These are available in the different ranges Hydraulic Jacks.

Product Details:

Standard Proctor Compaction Set:

• Consists of 100 mm dia. X 1000 cc volume mild steel mould with base plate & collar and 2.6 kg x 310 mm controlled fall steel rammer (standard)

Modified Proctor Compaction Set:

• Consists of 150 mm dia. X 2250 cc volume mild steel mould with base plate & collar and 4.89 kg x 450 mm controlled fall steel rammer (modified) .

Additional Information:

• Item Code: ST-02

Product Details:

 Split-spoon samplers as per ASTM D156 &  BS 1377 are used for taking samples for lithological descriptions, geotechnical analyses that do not require undisturbed samples, and chemical analysis. The use of liners in split-spoon allows collection of representative samples suitable for chemical analysis of all types of contaminants. Spit-spoons consist of a barrel that is attached to a drive tip. Sampling is accomplished by attaching the spit-spoon to the end of a DP extension, lowering it to the bottom of a borehole, then driving it into the soil with a geotechnical hammer.

 

Advantages include:

 

• Easy to obtain samples in unconsolidated materials above 100ft.

• Produce very good-quality samples for both lithological description and chemical analysis.

• Relatively efficient and inexpensive at shallow and intermediate depths Split Spoon Sampler SPT(Standard Penetration Tooling), Split Spoon Sampler for Geotechnical Sampling

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Permeability is very important engineering property to study the behavior of soil in respect of natural conditions and underthe flow of water. The permeability is dependent on particlesize and shape, density and degree of saturation. The instrument used to measure soil permeability is often calledpermeameter also. These may be either constant head or falling head or combined head. Constant head permeability apparatus is used basically for coarse grained materials such as sand andgravel whereas falling head is more appropriate for fine grained soils such as clay or silty soil.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: JNPT
• Production Capacity: 50/Month
• Delivery Time: 3-4 Weeks
• Packaging Details: Export Worthy Packaging

Product Details:

We are manufacturer & supplier of Field Density Apparatus Sand Replacement Method. As per IS: 2720 (Part XXVIII) The apparatus is used to determine dry density of coarse, fine and medium grained soils. It consists of a cylinder fitted with conical funnel and shutter and calibrating container, metal tray 300x300x40mm with 100mm hole in the center. Cylinder dia. 100mm, capacity 3 lit.

Specifications:

• Other sizes available: 150mm (10 lit) & 200mm (16.5lit)

Additional Information:

• Item Code: ST-17
• Port of Dispatch: JNPT
• Production Capacity: 100/Month
• Delivery Time: 2-3 weeks
• Packaging Details: Export Packaging

Product Details:

Electromagnetic sieve shaker 918 control is used in research & development, quality control of raw materials, interim and finished products as well as in production monitoring. The controllable electromagnetic drive offers an optimal adaption for every product. Sharp fractions are obtained even after short sieving times.
These Sieve Shakers are activated by electromagnetic impulses, they are recommended to perform sieving tests where high precision and performance are important, and where continual and intense uses are required.

It is particularly designed for test sieves with a diameter of 200 mm x 50mm h. They are therefore suggested for accurate sieving tests, also on fine materials. These Electromagnetic Shakers are of simple and sturdy construction, can hold up to 8 sieves

Additional Information:

• Delivery Time: 1-2 weeks

Product Details:

We are Manufacturer, supplier and exporter of Swell Test Apparatus from Mumbai, Maharashtra, India. It is designed to determine the swelling pressure developed by soil specimens moulded to desired densities at known moisture contents, when soaked in water. The load applied to restrain the swelling is transferred on to a load measuring proving ring through a perforated swell plate and a load transfer bar. The proving ring is attached to the lead screw of hand operated load frame. A soaking tank is provided for saturating the specimen and the base of the mould provided has channels and radial grooves with connecting holes.

The outfit comprises the following:

• One loading unit Hand. operated 5000 kg capacity with two rates of travel
• One Gun metal mould, 100mm dia x 127.3 cm height X 1000 cc volume with base plate & collar
• One perforated swell plate 100mm dia X 16mm thick
• One spacer 100mm dia X 12.7mm thick
• Two porous stone of 100mm dia X 12.7mm thick
• One load transfer bar
• One steel ball & one soaking tank, 250mm dia x 210mm high
• Dial gauge 0.01mm X 25mm travel
• Proving ring of 2.5 KN capacity with calibration chart and carrying case.

Optional Accessories:

• High sensitivity Proving Ring, 250 kg or 500 kg fitted with 0.002 mm dial gauge with certificate in a nice wooden carrying case.
• Dial Gauge 0.01mm x 25mm travel.

Product Details:

We are manufacturer, suppliers for Shrinkage Limit apparatus. Consists one each of Porcelain evaporating dish, Shrinkage dish, Glass cup, Perspex prong plate with three metal prongs, Perspex plain plate, Spatula, Plastic Cylinder 25 ml. Without mercury.

Additional Information:

• Item Code: CT-04

Product Details:

We are supplier of moisture tins. To determine moisture contents in soil and other material. These are made from aluminum or stainless steel.

Sizes available are:

• 50 mm dia
• 100 mm dia.

Additional Information:

• Item Code: ST-08

Product Details:

We are exporter supplier of Laboratory Vane Shear Apparatus.

Optional Extra:

• Consists of a torque head, adjustable in height by means of a lead screw rotated by a drive wheel to enable the vane to be lowered into the specimen. Rotation of the vane is by means of an electric motor which operates a worm gear arrangement turning the upper end of a calibrated torsion spring. The vane shaft is attached through the hollow upper shaft to a resettable pointer which indicates the angle of torque on a dial graduated in degrees. The dial reading multiplied by spring factor gives the torque.

Additional Information:

• Item Code: ST29

Product Details:

Triaxial Cell, for 38 mm dia. x 76 mm high specimen for lateral pressure upto 10.5 kg./cm2 ( 0 – 150 ) psi. This product is made and designed by making use of quality components and latest technology under the supervision of professionals.

 

Features:

• Anti-corrosive
• Quality tested

Product Details:

Using a speedy moisture meter, the moisture content of soil, sand and other fine grained material can be obtained quickly with reasonable accuracy. The test technique is based on the fact that water will react with calcium carbide to form acetylene gas and the quantity of gas formed is directly proportional to the water present, leaving a surplus of the chemical used in the test. The quantity of acetylene gas produced is indicated on a built-in pressure gauge which is calibrated in percentage of moisture on wet weight basis. A conversion formula gives the corresponding moisture content based on dry weight.

 

Application:

• Determination of Moisture Content

Product Details:

It is a fast ,accurate method to derive direct moisture % in a sample by Loss on Heating Method. Heating arrangement consists of a 250 watt heating lamp with a solid state power stat to control rate of drying and also temperature.

Product Details:

We are manufacturer supplier of Pocket Penetrometer. This instrument is used to estimate approximate unconfined compressive strength and the estimation for shear strength of soil. Cohesive soils can also be classified in terms of consistency using this penetrometer. This is a handy and convenient instrument.

Specifications:

• It cosists of a light weight barrel assembly with a polished and ground steel loading piston plunger.
• A direct reading scale is engraved on the piston barrel and indicates load in kg./sq.cm.
• A maximum load indicator ring is provided on the penetration plunger.
• The calibrated spring is heat treated and plated for rust resistance.

Additional Information:

• Item Code: ST-22

Product Details:

We are manufacturer & supplier of Load Frames from India Mumbai.
Load frames are used to apply load on the test specimen. The capacity and speed depends on the requirement of a particular test. Load frames are used in C.B.R. triaxial, unconfined compression test etc.

Additional Information:

• Item Code: ST-20