Material Testing Equipment

Product Details:

Liquid limit is that water content at which a part of soil cut by a groove of standard dimension will flow together for a distance of 1.25cm under air impact of 25 blows in a standard liquid limit apparatus. It consists of a brass cup held on adjustable brackets. It is supplied with grooving tools along with a 10mm gauging block to adjust the height of blow. A counter is also fitted to register the number of blows.

Additional Information:

• Item Code: ST-04

Product Details:

• Cylindrical Metal Measures as per IS: 2386 Part - III
• For determining the bulk density or unit weight of aggregates. .
• Specification of Size: 3 liter, 15 liter, 30 liter
• Cylinder made of Steel sheet material and both side carrying handle and one tamping rod 16 mm dia x 600 mm long.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Ref. Standards IS:9669, IS: 2720 (Part XVI), BS 1377; 1924; EN 13286-47/ ASTM D 1883; AASHTO 193

 

The California Bearing Ratio test, (usually called CBR test) is an empirical test developed in California, USA for determining the Relative Bearing Ratio and expansion characteristics under known surcharge weight of base, sub-base and sub grade soils for the design of roads, pavements and runways. The CSR test is used extensively in selection of materials and control of subgrades. The test can be performed in the laboratory on prepared samples or in-situ on location. It is important to appreciate that this test, being of an empirical in nature, is valid only for the application for which it was developed i.e., the design of highway base thickness.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

We are offering Universal Testing Machines , Mechanical and Computerised with all required accessories for Test. 

Features:

• Easy to operate

• High durability

• Sturdy construction

• Low maintenance

Product Details:

Details:

• Continuous roll autographic recorder supplied as standard to enable study of the behavior of materials
• Motor driven geared shafts for quick effortless adjustment of cross-head-to facilitate rapid fixing of test specimen.
• High reading accuracy due to large size and design of dial.
• Wide range of standard and special accessories, including load stabilizer.
• Large effective clearance between columns enables testing of standards specimens as well as structures.
• Simple controls for easy of operation.
• Robust staining frame of an extremely rigid construction.
• Safe operation ensured be means of safety devices.
• Control Panel: The control Panel consists of a power pack complete with drive motor and an oil tank, control valves a pendulum dynamometer a load indicator system and an autographic recorder.
• Power Pack: The power pack generates the maximum pressure of 200 kgf/cm2 the hydraulic pump provides continuously non-pulsating oil flow. Hence the load application is very smooth.
• Hydraulic Controls: Hand operated wheels are used to control the flow to and from the hydraulic cylinder. The regulation of oil flow is infinitely variable incorporated in the hydraulic system is a regulating valve which maintains a practically constant rate of table movement.
• Load Indicator System: This system consists of a large dial and a pointer. A dummy pointer is provided to register the maximum load reached during the test. Different measuring ranges can be selected by operating the range selection knob. An overload trip switch is incorporated which automatically cuts out the pump motor when the load range in use is exceeded.
• Pendulum Dynamometer: This unit permits selection of favorable hydraulic ratios producing relatively small frictional forces. Pressurised oil in the loading cylinder pushes up the measuring piston proportionately and actuates the special dynamometer system. The piston is constantly rotated to eliminate friction. The dynamometer system is also provided with an integral damper and ensures high reliability of operation. The load transmitted to the dynamometer is transferred through a pendulum to the load indicator.
• Autographic Continuous Roll Load-Elongation Recorder: This unit is of the pen and drum type and is supplied as standard. The horizontal motion of the pen produces the load ordinate of the diagram and the drum rotation produces the extension ordinates in the ration of either 1:5 or 1:10. A continuous roll of graph paper is stored inside the drum and is easily replaced.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

We are supplier of Spring Testing Machine (hand-cum-electric operated). Spring testing machine enable load deflection tests of tension and compression springs to be carried out accurately and quickly. The cabinet contains the hydraulic unit the hand wheel of the pump and the release valve handle are outside the cabinet for easy operation. This compact base carrier two fixed upright and four horizontal plates. The first and the third plates with two small uprights from an adjustable frame. The second and the fourth plates are fixed. A square threaded wheel arrangements provided for adjusting the height of the springs. A bourdon type gauge is fixed for direct load measurements. One fixed upright is graduated to denote the deflections or tension of the springs for direct readings. A thimble with on arrow mark is provided to facilitate the readings.

Additional Information:

• Item Code: MT-06

Product Details:

Cylindrical Metal Measures As per IS:2386 (Part 3)

Consists of one each of the following measures:

Measure 3 litres

Measure 15 litres

Measure 30 litres Supplied Complete with  Tamping Rod of 16mm dia x 60 cm long having 

Additional Information:

• Item Code: MT03

Product Details:

Universal Testing Machine is designed for testing metals and other materials under tension, compression bending, transverse and shear loads. Hardness test on metals can also be conducted.
1000KN, is designed to perform tensile, compression, bending and shear tests on most widely varying materials, both in form of test pieces and as finished products. Hardness test on metals can also be performed.

Salient Features:

• Loading Accuracy as high as ±1%
• Straining rate to cover a wide range of materials
• Continuous roll type load elongation recorder
• High reading accuracy due to large size and design of dial
• Simple controls to facilitate ease of operation
• Fully enclosed and protected load measuring system
• Wide range of standard and special accessories including load stabilizer Robust straining frame Suitable for standard specimen and also structures.
• Motorized UP / DOWN movement of lower crosshead to enable easy and rapid fixing of test specimen.

Auto load selection facility:

• The machine consists of Straining Unit, Control panel (Power pack, complete with drive motor and an oil tank, control valve, a pendulum dynamometer, a load indicator system and an autographic recorder.

Additional Information:

• Item Code: MT-09
• Port of Dispatch: Jawaharlal Nehru Port
• Production Capacity: 10 per month
• Delivery Time: 3-4 weeks
• Packaging Details: Wooden packing with strong base

Product Details:

We are manufacturer supplier of Torsion Testing Machine. Suitable for Torsion and Twist test on various metal rods and flats. Torque Measurement by pendulum dynamo meter system. Auto torque selector to adjust torque ranges. Geared motor to apply torque to specimen through gearbox.

Additional Information:

• Item Code: MT-10

Product Details:

We are manufacturer exporter of Falling head permeability test apparatus-Constant Head Test. As Per IS 2720 (Part XBII)- 1966 BS 1377, EN DD ENV 1997-2, ASTM D2434, AASHTO T215
This equipment is used for testing the permeability of granular soils (sands and gravels).The specimen is formed in a permeability cell and water is passed through it from a constant level tank Take-off points located along the sides of the permeability cell are connected to three manometer tubes mounted on a panel complete with a metre scale. Water passing through the specimen is collected and measured, either for a specific quantity or over a period of time. The reduction of head is noted from the variation of water level in the manometer tubes. Comprising three glass tubes of constant bore, metre scale and connecting tubing for cell pressure take-off points, all mounted on a free-standing panel. Manufactured from transparent plastic with attachment for wall mounting. The inlet, outlet and overflow pipes are fitted to the base of the tank and can be adjusted for height within the tank. Supplied complete with connecting tubing.

Product Details:

Globetrek engineering corporation is manufacturer suppliers & exporter of Jaw Crusher. Aggregate Jaw Crusher is especially designed for fast crushing of aggregates ores, minerals, coke, coal, chemicals and similar materials. Our Aggregate Jaw Crusher is compact and of rugged construction for general laboratory and small pilot plant operations.
Functionality : This laboratory jaw crusher is available with two jaws of manganese steel. The mobile jaw creates two blows for every revolution thereby minimizing the sizing to a minimum. A combination of downward and forward strokes having a rocking action exerts pressure on the coarser material, yet allows the finished material to move through the jaws. For feeding material, a hopper is available on the top. The smooth jaws ensure a uniform product thereby allowing easy cleaning.

Additional Information:

• Item Code: CTE-05