Civil Structural Monitoring Instruments

Product Details:

Globetrek Test Sieves are manufacturered in different Sizes , Diameter , Heights & Various national and international Standards . These are mainly Useful for particle size analysis of soil Chemical Powder Cement Aggregates etc Sieving is commonly used for Gradation and Particle Size Determination .

Globetrek manufactures Frames of Test sieves in Various materials like Brass , Stainless Steel 304 , Stainless Steel 316 & GI Material . Also diameter of sieves range from 4 " to 18 "

Product Details:

Specification:

3. 50 (3-1/2") white pvc, double check ball bailer, slurry samplerbailer diameter: 3-1/2"overall length: 20"chamber length: 12"construction: pvc body and lifting bailfdot approved: yes, for drilling fluid slurry testing

Product Details:

FOR REPLACING PRESSURE GAUGE AND DIAL INDICATOR IN PLATE BEARING AND PILE LOAD TESTS

Whenever we enter into pit to read the  movement, we wish to have one remote movement measuring device to tell movement at a convenient place. Often our pit is full of water or mud and entering below heavy load is always risky. To abandon old pressure gauge and dial indicators, we have designed a NEW system to provide load and movement measurement, remotely at convenient location and that’s too conveniently with recording facility.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

The Rockbolt Pullout Tester is manufactured for conducting anchor pullout test in rock, for the evaluation of bond strength between reinforcement and grout concrete or grout concrete and rock. In this test it is considered that the diameter of the anchor bar or rockbolt in rock, throughout the length of hole is uniform and grout density and quality is also uniform.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Joints in concrete pavements of highways, airport runways and container areas areexposed to stresses and strains due to traffic and temperature variation. Steel dowel barsand tie bars are built into joints, to support the transfer of loads across the joints and and tomaintain the elevation of adjacent slabs at the joints. The type and the number of dowels andtie bars as well as their accurate positions and tolerable displacements are accurately determined, to ensure the long-term performance of the joints.

Product Details:

The Roughometer 4 continues a tradition established over twenty years, providing easy, reliable road roughness measurements.

Key benefits

• Cost effective
• Provides simple, portable and highly repeatable measurements of road roughness
• Wireless distance sensor
• Wireless one-person operation on most Android phones and tablets
• Processing software formats data into easy-to-understand custom graphs, tables and maps

Product Details:

• Resolution: 0.01 mm,'0.0005"
• Buttons: On/off, zero, mm/inch
• Automatic power off, move the digital unit to turn on power
• Battery CR2032
• Data output

Product Details:

Casagrande type Porous Tube Piezometers are used for measuring and controlling pore water pressure in soil, rock and to monitor the construction control and stability in embankments, dams and reservoirs. A standpipe, with a porous piezometer tip connected at its lower end, is installed in a borehole. Bentonite and/OR grout are used to seal the borehole above the "tip". The water level inside the "standpipe" is measured with the help of a Electronic water level Indicator, and corresponds to the water pressure at the piezometer elevation. Permeability of soil in the vicinity of the tip can be determined, when required, by increasing the water head in the standpipe, and observing it's dissipation rate. Advantages:- (a) Ideal fordermining the piezometric level during routine site investigation. (b) Can also be installed after the completion of construction & therefore suitable for use in existing dams/embankments.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Delivery Time: 1-2 week

Product Details:

Flat Jack Test Insitu Stress Measurement Apparatus, complete ready to use with flat jack, pressure transducer, electronic extensometer, hose pipe, pump, 8 channel Data logger

 

Flat Jack Test can be used to determine in-situ Stress, Deformability and Resistance of masonry or other structures. This test is carried by cutting a slot into the structure to accommodate flat jacks or two, keeping the second jack at perpendicular to the previous one. This flat jack is than pressurized to desire level and related strains in adjoining area is read. For Stress measurement a single flat jack can be used BUT for deformability and Resistance

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

Whenever we enter into pit to read the movement, we wish to have one remote movement measuring device to tell movement at a convenient place. Often our pit is full of water or mud and entering below heavy load is always risky. To abandon old dial gauges, we have designed a NEW system to provide movement measurement, remotely at convenient location.

Features

• Rugged Stainless Steel piston• Over 20 hours battery backup• Spring loaded for bothway movement• Improved circuitry to achieve 0.1% accuracy• Display of all 4 channels on single screen• Direct connection to your computer (optional)

Product Details:

Inclinometer is a sensitive sensors providing deflection in between pairs of wheels, spaced at 500 mm apart. The sensor may be biaxial servo accelerometer based or vibrating wire or electrolytic sensor, provide deflection readings over Digital Indicator. When we insert Inclinometer probe into properly grouted casing, measurement of lateral movement or earth and structures is found.

Additional Information:

• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Mumbai